The TY6300Z is a 2-position (on/off) thermostat for indoor farm or horticultural applications. It automatically operates equipment such as a heater, hot water boiler, or fan for a greenhouse, crop-storage silo, or livestock barn.

Catalog (PDF/58KB)

The TY6800Z and TTY6800Z are thermostats with a remote sensor that can be inserted into an air duct or into liquid in a tank or pipe. These devices automatically control solenoid valves, motor valves, electric heaters, compressor motors for air conditioning equipment or heating/cooling equipment, etc.

Catalog (PDF/69KB)

The L91B/D controllers sense pressure changes, thus actuating an internal potentiometer and changing the electric resistance of the potentiometer in proportion to those changes.
The controllers are suitable for direct control of the proportional motors of automatic burners inside high limit controllers or for steam heater equipment.

Catalog (PDF/74KB)

The L404F senses pressure changes and activates internal switch, resulting in ON/OFF action of an electric circuit.
The controller makes and breaks the connection to solenoid valves or electric motor valves, and is used for pressure control involving fluids, air or steam. It is also used as a limit control or alarm switch.

Catalog (PDF/72KB)

Specification Sheet (PDF/425KB)

The C6065 functions as a combustion airflow supervisor, with a safe start interlock, suitable for positive or negative pressure applications.
This switch can be used with air or any normal product of gas combustion.

Catalog (PDF/49KB)

The C6097A gas pressure switch is used to detect the pressure of city gas, natural gas, LP gas, air, etc.
The switch performs ON/OFF control of an external electrical circuit in accordance with the set point. This switch has a wide range of uses, such as detecting the upper or lower limit pressure of gas or air to be supplied to a gas combustion system, or detecting a clogged interlock filter on a burner blower.

Catalog (PDF/56KB)

User's Manual (PDF/1.01MB)

The MC150S-JY is a float chamber type water-level controller used for water-level control of a middle pressure boiler or water storage tank and for burner cutoff at water-level drop below the low limit. A bellows seal structure is applied between liquid wetting area and switching unit. One mercury switch is used for start/stop of a water supply pump, and another mercury switch is used for burner cutoff and low water alarm at abnormal drop of water level.

Catalog (PDF/51KB)

The FS1-J/W flow switches are orifice type, highly sensitive flow switches for mounting in 1/2'' (B) pipe of a process pipe run, and are used for water cut-off relays to detect the water flow or level.
Because the flow sensing section is composed of an orifice and a diaphragm with a magnet connected to a microswitch, it is highly sensitive, durable and highly reliable. Flow rate to operate or stop the switch can be set by a flow rate adjustment screw.

Catalog for FS1-J (PDF/51KB)

Catalog for FS1-W Splash-Proof Model (PDF/50KB)

The FS4-3J flow switch is a paddle type flow switch to be mounted in 1 to 6 (B) pipe of a water process pipe run, and is used to detect water flow or level for a water cut-off relay.
The flow sensing section is composed of a paddle and bellows that operate a microswitch when the flow changes. The flow rate that operates or stops the switch can be set by an adjustment screw.

Catalog (PDF/56KB)

The FS7-4 flow switch is a paddle type flow switch for mounting in 1 1/4 to 6" (B) pipe of a process pipe run, and is used for a water cut-off relay to detect the water flow or level.
Because the flow sensing section is composed of a paddle and a sealed stainless tube with a magnet connected to a microswitch, it is highly sensitive, durable and highly reliable. The settings of switch actuation by the flow rate that operates or stops the switch can be set by an adjustment screw.

Catalog (PDF/75KB)

The FS8-WJ splash-proof flow switch is a paddle type flow switch for mounting in 1" to 6" (B) pipe size of a process water pipe run and is used for a water cut-off relay to detect the water flow or level.
The flow sensing section is composed of a paddle and a sealed bellows that actuate a microswitch by sensing changes in the flow rate. The settings of switch actuation by the flow rate and no-flow rate can be made with an adjustment screw.

Catalog (PDF/55KB)